Search

You can find the results of your search below.

Fulltext results:

NFTables Configuration
15 Hits, Last modified:
routing.</color>\\ <tab6><color blue> # open ports refers to ports to open for input to this machine.</color>\\ <ta... #202000/#F0F0E0> Incoming WAN packets to the mail ports, pop3s, imaps or smtp ports are preroute dnat to the mail server IP address.<... <tab6> }\\ <tab3> }\\ ++++ ++++mail server ports:| * smtp {25} / (smtps) submissions {465} / sub... {587} - (My mail server uses smtp / submission on ports 25 / 587 respectivily) * imap {143} / imaps {99
Wireguard VPN access from WAN to LAN
15 Hits, Last modified:
routing.</color>\\ <tab6><color blue> # open ports refers to ports to open for input to this machine.</color>\\ <ta... #202000/#F0F0E0> Incoming WAN packets to the mail ports, pop3s, imaps or smtp ports are preroute dnat to the mail server IP address.<... list table ip nat -a'' * To add a set tcp_open_ports in inet firewall: ''sudo nft add set inet firewall tcp_open_ports{type inet_service \; flags interval \;}'' * To add elements to set tcp_open_ports: ''sudo nft add element inet firewall tcp_open_ports{ssh, http, 60000-61000 }'' * To delete rule in
Router Miscellaneous
13 Hits, Last modified:
in Linux]] * [[https://www.stationx.net/common-ports-cheat-sheet/|Common Ports Cheat Sheet: The Ultimate Ports & Protocols List]] * [[https://www.geeksforgeeks.org/50-common-ports-you-should-know/|50 Common Ports You Should Know]] * Distribution List of Ports (information only) * <fc #ff00ff>Gentoo</fc> [[http
NFTables IP Control
8 Hits, Last modified:
e forward and nat chains refer to routing. # open ports refers to ports to open for input to this machine. # ssh is port ... e are not using yet. # set tcp_open_ports { # type inet_service; flags interval; # ... # https # } # set udp_open_ports { # type inet_service; flags interval; # ... nter accept # allow tcp/udp open ports # tcp dport @tcp_open_ports counter acce
Router VM
7 Hits, Last modified:
ng as a network switch for the connected physical ports. (On my home server I have 4 x 1GB/s Ethernet ports and an add in PCIe card that provided a 2.5GB/s Ethernet port. All these physical ports are connected to a common network bridge device. ... t allows connections of multiple virtual Ethernet ports to the bridge device. This is a commonly used fea
Router Hardware
5 Hits, Last modified:
SO-DIMM DDR5 4800MHz, 32GB(SAMSUNG). *Ethernet Ports: 2 x Marvell AQC113C-B1-C 10Gbps Network cards(vi... : 2 x M.2 2242/2280 NVMe SSD, PCIe 2.0 x 1 *USB Ports: 2 x USB-A 3.0(5Gbps), 1 x USB-C 3.2 Gen2(10Gbps)... wer (~8 - 10W), small size. They come with 2 SATA ports and mini PCI-E slots. By the time you fit them ou... -Lucent G-240G-P'' (at least up to circa 2025) 1 ports are G-010G-D and FG1000ANB 4 ports are U-040X-A a
Debian Server Network Setup
4 Hits, Last modified:
ing 3 NICs are setup in bridge mode as router LAN ports. When setup in bridge mode the 3 ports effectively act as a switch with any able to acce
Linux Router Background
3 Hits, Last modified:
TP-Link VDSL modem router with 4 100Mbps ethernet ports and 2 VoIP port. One ethernet port was set up as ... outer was a N3700 router with 4 1000Mbps ethernet ports running Linux Debian. -The 2500/10000Mbps ether... uter with 2 x 2500Mbps and 2 x 10000Mbps ethernet ports running Linux Debian. (The WAN is connected to a
Wifi Router / Access Points
2 Hits, Last modified:
D Flash and 512MB RAM. It has 4 x 1Gbit ethernet ports and 1 x 2.5Gbit ethernet port. The WAX206 does n... D Flash and 128MB RAM. It has 5 x 1Gbit ethernet ports. It has 1 x USB 3.0 port. Only having 8MB flash
IPTables Configuration
1 Hits, Last modified:
e WAN -A POSTROUTING -o ppp1 -j MASQUERADE # WAN Ports DNAT to LAN -A PREROUTING -p tcp -m tcp -i ppp1 -
DHCP / DNS Setup
1 Hits, Last modified:
SchedulingPolicy=idle # Allow for binding to low ports and doing raw network access CapabilityBoundingSe