https://wiki.kptree.net/ 2026-09-23T19:00:18+00:00 https://wiki.kptree.net/ https://wiki.kptree.net/_media/wiki:dokuwiki.svg text/html 2022-01-16T03:37:00+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.kptree.net/linux_router:nftables_control?rev=1642304220&do=diff linux nft nftables nmap NFTables IP Control I primarily set this feature up to act as a form of parental control on my home internet access. Disable Range of IP addresses, with count-down timer The DHCP assigned addresses in the range 100 - 254 were to be disabled (dropped) in the evening. The addresses below 100 were assigned a specific IP address in the DHCP based upon MAC. text/html 2025-11-30T10:55:19+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.kptree.net/linux_router:network?rev=1764500119&do=diff linux debian ubuntu router network netplan interface vlan ipv6 ip Debian Server Network Setup Debian Network - Server Interface Setup As of Debian 10 (Buster) Debian still by default uses this interface Setup. It can be setup to use netplan inface. Ubuntu (as of version 14.04) defaults to Predictable Network Interface Names, also see Systemd Docs. I have no problem with this. In any case, you should always check dev names and not assume names, such as text/html 2026-07-12T13:14:44+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.kptree.net/linux_router:tc?rev=1783862084&do=diff linux router tc traffic control TC - Traffic Control The Linux kernel's network stack has network traffic control and shaping features. The iproute2 package installs the tc command to control these via the command line. Queuing controls how data is sent; receiving data is much more reactive with fewer network-oriented controls. However, since TCP/IP packets are sent using a slow start the system starts sending the packets slow and keeps sending them faster and faster until packets start getti… text/html 2024-12-15T03:35:46+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.kptree.net/linux_router:dns_dhcp?rev=1734233746&do=diff linux router dns dhcp bind ip ipv6 radvd host dig nslookup DHCP / DNS Setup Outdated I have moved my DNS and DHCP servers to Docker, Docker-DNS Server. I am still using ISC_Bind9, but am now using ISC_Kea for DHCP as ISC_Bind is no longer supported as of 2022. tl;dr; Further to this I am not looking at backups for both these services on my local area network. Whilst these services worked reliably well, when ever I shutdown the the router with text/html 2024-09-21T12:10:33+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.kptree.net/linux_router:ppp?rev=1726920633&do=diff linux router pppoe pppoed isp mtu dns dhcp ISP PPPoE Network Setup A reasonably comprehensive discussion on Ubuntu forums Setup Ubuntu Server as a router using a PPPoE connection, MTU and TCP MSS when using PPPoE. Also from Ubuntu forums How to Optimize your Internet Connection using MTU and RWIN. Ubuntu documentation ADSLPPPoE. PPPD manual page. Another reference is Confirm Blog Using PPPoE on Linux. Some other references: * Connecting to NBN HFC with a linux router] Internode router set… text/html 2025-05-24T13:09:25+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.kptree.net/linux_router:wireguard?rev=1748092165&do=diff linux router vpn wireguard docker qr_code qr Wireguard VPN access from WAN to LAN I use a Docker instance for my Wireguard server now. I use 2 forms of vpn (virtual private network) on my home server. * VPN to gain remote secure private access to my home LAN from the WAN (internet). This is the one I am describing here. text/html 2026-01-31T11:03:52+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.kptree.net/linux_router:wifi?rev=1769857432&do=diff linux router wifi wifi_router access_point Wifi Router / Access Points I prefer to run higher quality wifi access points (AP) than the all in one type routers. My current router is X86 based running Linux Nftables on bare metal and Bind9 and Kea as well as some other services in Docker on a VM.