Search
You can find the results of your search below.
Matching pagenames:
Fulltext results:
- Docker mailserver @docker_notes
- ptree.net''. This will only be accessible on the LAN. ====ISPmail Admin==== I will setup DNS and Traef... ptree.net''. This will only be accessible on the LAN. Admin user is mailserver with associated passwor... uting of STARTTLS. At least as of 2023-12-02. My LAN DNS points to the one common IP address for the m
- Nextcloud Container @docker_notes
- he Collabora server unless it is operating on the LAN. It is not difficult for me to setup the Collabor
- Docker Deluge Image / Service @docker_notes
- N to gain remote secure private access to my home LAN from the WAN (internet). //This is where I descri... router:wireguard|Wireguard VPN access from WAN to LAN]]//. - VPN to anonymize my public internet acce... '' under under output chain: *''oifname $lan ip daddr 103.231.89.219 counter accept #Host: au-per.pvdata.host'' * where $lan is set to lan interface, e.g. enp1s0 * ''%%doc
- Docker @docker_notes
- cate outside the local host IP address with other LAN addresses, including the router / gateway. Linu... br0 was the bridge interface for the VMs and also LAN access. The next problem was how to make this oc
- turn server @docker_notes
- NAT for this reason. If NAT is not used with IPv6 LAN then the local address area is directly accessibl
- dokuwiki setup notes @home_server
- l dns setup==== The local dns points to the local lan address that assists with hairpin nat on ipv4. No
- Linux Router Background @linux_router
- n alternative. All the services still work on my LAN except the email server. (The email server does actually operate on my LAN but it pretty pointless without access to externa
- Router Hardware @linux_router
- l Pentium N3700 system with 4 x Intel i210-AT GbE LAN. I got with maximum 8GB RAM and 120GB mSata HD. ... l Pentium N3700 system with 4 x Intel i210-AT GbE LAN, from [[https://mitxpc.com/products/sys-e200-9b|M... d power slightly lower than the J1900. (The Intel LAN controllers are also the more modern ones). This unit also comes with a dedicated IPMI LAN Port, allowing full remote KVM operation on the n
- Docker - DNS Server @docker_notes
- sive Guide]]\\ I have been using Bind9 as my home LAN DNS for the past few years. I originally operated
- Webmin @home_server:home_server_setup:other_services
- Fortunately as I only wish to run Webmin locally (LAN), not facing the public internet (WAN), I can sti
- IPMI Console Setup @home_server:home_server_setup:other_services
- elects IPMI interface to use; options seem to be: lan for IPMI 1.5 and lanplus for IPMI 2.0. (All my in... elects IPMI interface to use; options seem to be: lan for IPMI 1.5 and lanplus for IPMI 2.0. (All my in... sol : Configure and connect IPMIv2.0 Serial-over-LAN * activate : to activate the terminal connectio... Hence it should only be operated in a restricted LAN, where only strict secure outside control is poss
- IPMI CLI Tools @home_server:home_server_setup:other_services
- h the machine locally. This is called Serial Over Lan (SOL) and is available in IPMI v2.0 as a standard... v1.5 - Ability to send IPMI messages to BMC over LAN, LAN alerting. No SOL as part of the standard's specification but some vendor specific SOL implementations. *IPMI v2.0 - Serial Over LAN enabling console redirection, access control, enh
- Router Miscellaneous @linux_router
- e some security benefits by obscuring the private LAN addresses from the public WAN. IPv6 does not use... nect to a physical network and even be assigned a LAN IP address. Bonding allows physical networking de
- NFTables Configuration @linux_router
- m device label</color>\\ <tab3>define <color red>lan = br0</color><color blue> #definition of lan device label</color>\\ <tab3>define <color red>lan_ip4 = 192.168.1.0/24</color><color blue> #definition of lan IPV4 range</color>\\ <tab3>define <color red>rout
- Network Setup @home_server:home_server_setup
- NIC connectors are setup as follows: <code> IPMI_LAN USB2-1 USB3-1 LAN3(eth2) LAN4(eth3) USB2-0 USB3-0 LAN1(eth0) LAN2(eth1) VGA </code> Edit the network configuration file: '