Search
You can find the results of your search below.
Matching pagenames:
Fulltext results:
- DHCP / DNS Setup @linux_router
- {{tag>linux router dns dhcp bind ip ipv6 radvd host dig nslookup}} ======DHCP / DNS Setup====== =====Outd... orked reliably well, when ever I shutdown the the router with DNS/DHCP servers my LAN would stop working. ... archive (tl;dr; roll-up) eventually. Actually my router that I was running these services was totally los... nger readily available, Kill-9 Ubuntu 16.04 based Router, Part 2 - DHCP| does not seem to be saved on [[ht
- Basic Netfilter Function Block Diagram @linux_router
- {{tag>linux router mtu netfilter }} =====Basic Netfilter Function Block Diagram===== Both NFTables and IP... bles, will probably take a long time.\\ {{:linux_router:linux_netfilter.png?600|}} <code> The following i... ) functions, which are the basic requirements for router. Incoming Packets | ... | Network Processes | | Forward | | within Router | | Rules | |-------------------|
- TC - Traffic Control @linux_router
- {{tag>linux router TC Traffic Control}} ======TC - Traffic Control====== The Linux kernel's network stack ... ved on a LAN by dropping packets that arrive at a router before they get forwarded. There are more relevan... https://www.b1c1l1.com/blog/2020/03/26/linux-home-router-traffic-shaping-with-fq_codel/|Linux Home Router Traffic Shaping With FQ_CoDel]] *[[https://www.b1c1l
- Router Configuration & Server Setup @linux_router
- {{tag>linux router "router configuration" setup debian ubuntu snap snaps}} ======Router Configuration & Server Setup====== =====Router Configuration===== <fc #ff0000>[DRAFT]</fc> A router perf
- NFTables Configuration @linux_router
- {{tag>linux router NFtables firewall}} =====NFTables Configuration===== The best reference for nftables is... thub.com/wolfhechel/db7ed3be31feb104752e|nftables router]]. The reference at stosb is good, but not for a router [[https://stosb.com/blog/explaining-my-configs-nf... lot of experimenting the following is my NFTables router configuration file. Create the following file cal
- Domain names, domain nameservers, DNS and DHCP @tech_notes
- iscovery for global IP addressing, with a DHCP or Router Advertisements. *Each hardware connection po... g functions are often limited, that is not all IP router functions are available on Level 3 switches.
- Reverse Proxy Server @docker_notes
- config.yml</code> I have broken down the Traefik router dynamic configuration file, My config.yml into 2 ... figuration files. One for the http/https specific router configuration and the other for the tcp router configuration, I do not use any UDP router configurations to date. I placed these files in the sub-direct
- Router VM @linux_router
- {{tag>linux router VM}} ======Router VM====== I have just decided to play with installing VM (virtual machines) on my Router hardware (2023-01). I have been reluctant to do ... mber of reasons. My separate listing for [[linux_router:hardware]]. Basically the machine is a bit old s
- Docker mailserver @docker_notes
- ARTTLS protocol is used. I could possibly use my router, but this is getting too complex. To allow opera... The webmail.kptree.net successfully used Traefik router and successfully operated with the mailserver on
- Docker Host @docker_notes
- r functionality. I use nftables as my main edge router / firewall on bare metal. I could probably run this on a VM within Proxmox, but the Router hardware is not especially powerful and at this t... reason for me to do so at this time. My current router has an Intel N3700 CPU, maximum 8GB ram, procured... ow to use, but still functions well as a sub gb/s router. I also run a VM with Docker containers for a ba
- Docker @docker_notes
- >//**A Docker host that is acting or running as a router, e.g. using Traefik, the following may be needed ... P address with other LAN addresses, including the router / gateway. Linux forwarding is required for Doc... rward''. It would also adversely affect my Linux router should I attempt to load docker on this machine. To make matters worse my Linux router is based on nftables which may not operate well w
- sidebar
- *[[docker_notes:nginx-php-notes]] ++++ ++++Linux Router Setup| *[[linux_router:start]] *[[linux_router:background]] *[[linux_router:hardware]] *[[linux_router:ubuntu]] *[[linux_router:network]] *[[lin
- IPv6 Setup Notes @linux_router
- netplan apply'' *https://www.tomicki.net/ipv6.router.php *https://netplan.io/examples *https://www... position 39 tcp dport domain counter'' <- linux_router:nmap|Prev page ^ linux_router:start|Start page ^ -> ^ linux_router:qemu|Next page ->
- Linux Router Setup Notes - Index @linux_router
- ======Linux Router Setup Notes - Index====== <pagelist&header> *[[linux_router:start]] *[[linux_router:background]] *[[linux_router:hardware]] *[[linux_router:ubuntu]] *[[linux_router:network]] *[[linux_route
- Docker - DNS Server @docker_notes
- I originally operated it on bare metal on my home router computer. In mid 2023 I successfully moved my Bi... slave instance in a container running on my home router computer. I created a Docker Bind9 Image using b... ne Linux images, with S6 init system. The main router must be set to forward packets! The ability to fo... he master *The secondary DNS server runs on my router, it is set up as a slave server from the primary