Search

You can find the results of your search below.

Fulltext results:

DHCP / DNS Setup
17 Hits, Last modified:
ed.conf.local'' *''sudo cp /etc/bind/named.conf.default-zones /etc/bind/default.named.conf.default-zones'' ====Bind9 Control Nomenclature==== There... ===Setting Bind9 to IPv4 Mode==== ''sudo vim /etc/default/bind9'' or ''sudo vim /etc/default/named'', set following parameter: ''OPTIONS="-u b... ment. ====isc-dhcp-server defaults file==== The default isc-dhcp-server configuration files is: ''sudo vim /etc/default/isc-dhcp-server''. Ensure the interface(s) that t... h system interface that is not assigned in ''/etc/default/isc-dhcp-server''. **//This is a warning, not an
Router Hardware
11 Hits, Last modified:
ot. For the permanent solution basically edit etc/default/grub, adding nomodeset such that GRUB_CMDLINE_LINUX_DEFAULT="nomodeset" and then execute "sudo update-grub". ... . Add 'GRUB_GFXPAYLOAD_LINUX=1024x768' to the etc/default/grub file. There are an number of other possible options, the default 640x480 and 800x600 are too small and the 1280x10... ect it totally ignores your parameter and goes to default. As I did not care about colour depth, I just use... reen by adding 'GRUB_GFXMODE=1024x768' to the etc/default/grub file. This help make use of the grub menu ea
Router Miscellaneous
6 Hits, Last modified:
====Docker Host Security==== Docker currently by default use iptables on the host machine to allow access to images. Unfortunately the default iptables effectively fully opens up docker on the... usr/bin/docker stop -t 2 algo [Install] WantedBy=default.target </code> Techcrunch.com [[https://techcrunc... on ftp-data 20 {tcp, udp, sctp} File Transfer [Default Data] ftp 21 {tcp, udp, sctp} File Transf
Debian Server Network Setup
5 Hits, Last modified:
up===== As of Debian 10 (Buster) Debian still by default uses this interface Setup. It can be setup to us... tocol #bridge_fd 9 # forwarding delay # use default? #bridge_hello 5 # use default? #bridge_maxage 60 # use default? </code> ++++ The following is a list of some stanza not used and wh
Wireguard VPN access from WAN to LAN
5 Hits, Last modified:
number wireguard is set to, in my case 51914, the default is 51820. This lets you see if the packets are c... h all the table chain is at the end drop (nftable default policy is accept, hence it is necessary to set so... h all the table chain is at the end drop (nftable default policy is accept, hence it is necessary to set so... ER_UP> mtu 1420 qdisc noqueue state UNKNOWN group default qlen 1000 link/none inet 192.168.6.1/24
Router Configuration, Switch & Server Setup
5 Hits, Last modified:
o have a manual address assigned that matches the default equipment address to allow allow access to the equipment to change the default access address to match that required. There a... t may not be the same address. Say the equipment default assigned address is 192.168.56.34, then the compu... een 2 - 254, except in this case 34, which is the default assigned to the equipment to be configured. *
ISP PPPoE Network Setup
4 Hits, Last modified:
se parameters ''man pppd''. <code> # Minimalistic default options file for DSL/PPPoE connections # man:pppd... he ISP. noipdefault # Use this connection as the default route. defaultroute replacedefaultroute #password is not placed in log file - default hide-password # Do not ask the remote to authent... sist # maxfail number of retries before exiting, default 10, 0 means no limit maxfail 0 # Load rp-ppoe.s
ISP IPoE DHCP Setup Notes
4 Hits, Last modified:
password and user name. It actually seems to use default username and password in the pppoe software that ... R_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd... AST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 0c:c4:7a:9f:36:4c brd ff... Link File: /usr/lib/systemd/network/99-default.link Network File: /run/systemd
NFTables Configuration
3 Hits, Last modified:
h all the table chain is at the end drop (nftable default policy is accept, hence it is necessary to set so... h all the table chain is at the end drop (nftable default policy is accept, hence it is necessary to set so... number (line numbers) *''-n'' : shows names (default), e.g. dport ssh *''-nn'' : shows numbers e.
IPTables Configuration
2 Hits, Last modified:
such as Docker and Fail2ban basically still have default enbedment of IPTables with use of NFTables requir... ands=== *''iptable -L'' , lists the tables, by default the filter table. To list the nat table, add ''-t
TC - Traffic Control
2 Hits, Last modified:
*''sudo sysctl -a | grep qdisc'' shows current default settings *''sudo sysctl -a | grep net.'' shows ... erface ''dev eno1'' it would seem that Linux has default settings for network interfaces, e.g.: <code>qdis
Wifi Router / Access Points
1 Hits, Last modified:
is saturated) =====/etc/config/uhttpd===== ++++ default /etc/config/uhttpd| <code>config uhttpd 'main' l